【英文标准名称】:Testconditionsformillingmachineswithtableofvariableheight--Testingofaccuracy--Part2:Machineswithverticalspindle
【原文标准名称】:工作台高度可调的铣床试验条件.精确度测试.第2部分:立式铣床
【标准号】:JISB6203-2-2007
【标准状态】:现行
【国别】:日本
【发布日期】:2007-09-20
【实施或试行日期】:
【发布单位】:日本工业标准调查会(JP-JISC)
【起草单位】:TechnicalCommitteeonIndustrialAutomation
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:
【摘要】:この規格は,JISB6191に基づいて,普通精度のはん(汎)用ひざ形立てフライス盤の静的精度及び工作精度の検査方法,並びにそれぞれの検査事項に対応する許容値について規定する
【中国标准分类号】:J54
【国际标准分类号】:25_080_20
【页数】:22P;A4
【正文语种】:日语
基本信息
| 标准名称： | 小丸瓶装机 |
| 英文名称： | Filling pill machine |
| 中标分类： |
医药、卫生、劳动保护 >>
制药、安全机械与设备 >>
制药加工机械与设备 |
| ICS分类： |
|
| 替代情况： | YY 0218.2-1995 |
| 发布部门： | 中华人民共和国国家发展和改革委员会 |
| 发布日期： | 2005-02-14 |
| 实施日期： | 2005-08-01 |
| 首发日期： | 1900-01-01 |
| 作废日期： | 1900-01-01 |
| 提出单位： | 中国制药装备行业协会 |
| 归口单位： | 制药装备行业标委会 |
| 起草单位： | 新中制药机械有限公司 |
| 起草人： | 黄喜华、朱湘一 |
| 出版社： | 中国计划出版社 |
| 出版日期： | 2005-08-01 |
| 页数： | 11页 |
| 批文号： | 发改委2005-7 |
适用范围
本标准规定了小丸装瓶机的分类和标记、要求、试验方法、检验规则和标志、使用说明书、运输、包装与贮存。
前言
没有内容
目录
没有内容
引用标准
没有内容
所属分类： 医药 卫生 劳动保护 制药 安全机械与设备 制药加工机械与设备
Product Code:SAE J2288
Title:Life Cycle Testing of Electric Vehicle Battery Modules
Issuing Committee:Electric Vehicle Forum Committee
Scope: This SAE Recommended Practice defines a standardized test method to determine the expected service life, in cycles, of electric vehicle battery modules. It is based on a set of nominal or baseline operating conditions in order to characterize the expected degradation in electrical performance as a function of life and to identify relevant failure mechanisms where possible. Accelerated aging is not included in the scope of this procedure, although the time compression resulting from continuous testing may unintentionally accelerate battery degradation unless test conditions are carefully controlled. The process used to define a test matrix of accelerated aging conditions based on failure mechanisms, and to establish statistical confidence levels for the results, is considered beyond the scope of this document. Because the intent is to use standard testing conditions whenever possible, results from the evaluation of different technologies should be comparable. End-of-life is determined based on module capacity and power ratings. This may result in a measured cycle life different than that which would be determined based on actual capacity; however, this approach permits a battery manufacturer to make necessary tradeoffs between power and energy in establishing ratings for a battery module. This approach is considered appropriate for a mature design or production battery. It should be noted that the procedure defined in this document is funtionally identicaly to the USABC Baseline Life Cycle Test Procedure.